Nanofluidic-Based Accumulation of Antigens for Miniaturized Immunoassay.

The continuous advances of Nanofluidics have been stimulating the development of novel nanostructures and strategies to accumulate very diluted analytes, for implementing a new class of high sensitivity miniaturized polymeric sensors. We take advantage of the electrokinetic properties of these structures, which allow accumulating analytes inside asymmetric microfluidic structures to implement miniaturized sensors able to detect diluted solutions down to nearly 1.2 pg/mL. In particular, exploiting polydimethylsiloxane devices, fabricated by using the junction gap breakdown technique, we concentrate antigens inside a thin microfunnel functionalized with specific antibodies to favor the interaction and, if it is the case, the recognition between antigens in solution and antibodies anchored to the surface. The transduction mechanism consists in detecting the fluorescence signal of labeled avidin when it binds to biotinylated antigens. Here, we demonstrate that exploiting these electrokinetic phenomena, typical of nanofluidic structures, we succeeded in concentrating biomolecules in correspondence of a 1 pL sensing region, a strategy that grants to the device performance comparable to standard immunoassays.

Integrating Microstructured Electrospun Scaffolds in an Open Microfluidic System for in Vitro Studies of Human Patient-Derived Primary Cells.

Recent studies have suggested that microenvironmental stimuli play a significant role in regulating cellular proliferation and migration, as well as in modulating self-renewal and differentiation processes of mammary cells with stem cell (SCs) properties. Recent advances in micro/nanotechnology and biomaterial synthesis/engineering currently enable the fabrication of innovative tissue culture platforms suitable for maintenance and differentiation of SCs in vitro. Here, we report the design and fabrication of an open microfluidic device (OMD) integrating removable poly(ε-caprolactone) (PCL) based electrospun scaffolds, and we demonstrate that the OMD allows investigation of the behavior of human cells during in vitro culture in real time. Electrospun scaffolds with modified surface topography and chemistry can influence attachment, proliferation, and differentiation of mammary SCs and epigenetic mechanisms that maintain luminal cell identity as a function of specific morphological or biochemical cues imparted by tailor-made fiber post-treatments. Meanwhile, the OMD architecture allows control of cell seeding and culture conditions to collect more accurate and informative in vitro assays. In perspective, integrated systems could be tailor-made to mimic specific physiological conditions of the local microenvironment and then analyze the response from screening specific drugs for more effective diagnostics, long-term prognostics, and disease intervention in personalized medicine.

Increased Flexibility in Lab-on-Chip Design with a Polymer Patchwork Approach.

Nanofluidic structures are often the key element of many lab-on-chips for biomedical and environmental applications. The demand for these devices to be able to perform increasingly complex tasks triggers a request for increasing the performance of the fabrication methods. Soft lithography and poly(dimethylsiloxane) (PDMS) have since long been the basic ingredients for producing low-cost, biocompatible and flexible devices, replicating nanostructured masters. However, when the desired functionalities require the fabrication of shallow channels, the "roof collapse" phenomenon, that can occur when sealing the replica, can impair the device functionalities. In this study, we demonstrate that a "focused drop-casting" of h-PDMS (hard PDMS) on nanostructured regions, provides the necessary stiffness to avoid roof collapse, without increasing the probability of deep cracks formation, a drawback that shows up in the peel-off step, when h-PDMS is used all over the device area. With this new approach, we efficiently fabricate working devices with reproducible sub-100 nm structures. We verify the absence of roof collapse and deep cracks by optical microscopy and, in order to assess the advantages that are introduced by the proposed technique, the acquired images are compared with those of cracked devices, whose top layer, of h-PDMS, and with those of collapsed devices, made of standard PDMS. The geometry of the critical regions is studied by atomic force microscopy of their resin casts. The electrical resistance of the nanochannels is measured and shown to be compatible with the estimates that can be obtained from the geometry. The simplicity of the method and its reliability make it suitable for increasing the fabrication yield and reducing the costs of nanofluidic polymeric lab-on-chips.

Apomyoglobin is an efficient carrier for zinc phthalocyanine in photodynamic therapy of tumors.

The spectral and the photophysical properties of phthalocyanines have made these dyes attractive for applications in photodynamic therapy of cancer. One important known issue of these compounds is their tendency to aggregate in aqueous media, which decreases their fluorescence, triplet, and singlet oxygen quantum yields. We report on the use of apomyoglobin as a carrier for zinc phthalocyanine (ZnPc) to overcome solubility limitations of the dye. We show that the protein is able to bind ZnPc in monomeric form, preserving its photophysics. Confocal fluorescence imaging of PC3 and HeLa cells, treated with the complex between ZnPc and apomyoglobin, demonstrates that the photosensitizer is uptaken quickly by cells. Illumination of treated cells strongly decreases viability, as demonstrated by live/dead fluorescence assay.

The Role of Surfaces in Gas Transport Through Polymer Membranes.

This paper describes a procedure to measure the permeability P, diffusivity D, and rate of adsorption k1, thus determining the solubility S and rate of desorption k2 of He, N2, O2, CH4, and CO2 on a polydimethylsiloxane (PDMS) membrane. The described procedure is able to determine experimentally all the physical quantities that characterize the gas transport process through a thin rubber polymer membrane. The experiments were carried out at room temperature and at a transmembrane pressure of 1 atm. The results are in good agreement with the available data in the literature and offer an evaluation of k1 and k2.